Monday, August 19, 2013

Two steps / one step [John]

Some progress since the last report! And some setbacks.


  • Brakes, early July
We bled the brakes and completed the overhaul, for now. First drive was a bit scary; moderate pedal pressure locked up one wheel, screeching the tire dramatically enough to attract attention from the neighbors. After a little deliberate heating of the brakes, braking was near normal (guessing at what normal is), and I think we are done with the brakes for now. Satisfied that the car will stop, we are turning to making it go.

  • Ignition tune-up, middle July

It took several trips to the parts stores and a bunch of time on the web doing research, but we finally identified the points, condenser, and distributor rotor this 330 ci hemi requires. Found them in stock at NAPA. I removed the distributor to install the new points and condenser, carefully setting the gap before reinstalling. Engine now starts fine and, maybe, runs a little better. Driving it around the block disclosed alarming backfire through the carburetor, a known cause of engine fires. It needs at least ignition timing adjustment. Let's see: if an intake valve doesn't close, could that lead to ignition of the fuel/air charge in the intake manifold? Let's get the timing right first.
  • Ignition timing, August 17. 
Easily located a timing pointer, drivers' side, but there were no timing marks visible on the vibration damper. After idling the engine while holding a wire brush against the damper, enough rust was knocked of that we could see some marks. Maybe a whole scale. But we could not read it, and it was too faint to use. With a dot of Wite-Out on the first and clearest mark, we adjusted the timing to match the pointer, hoping the mark is at the specified 8 degrees BTDC. The idle came way up with this adjustment, and the car ran well enough to drive to a gas station and Target (see next topic). But is it correct?

Template for a replacement floor pad
After a few blocks, it was clear that there are issues with the throttle linkage however. Takes too much force to operate, sticks in open position. A little more driving and the engine lost most of its power. Time to quit for the day though, so this will have to wait. Probably that lost power is caused by linkage defects, but could my forgetting to dab the grease (included with the new points) onto the cam-following block cause really rapid wear and ruin the gap?
  • Other improvements
The steering column pad that keeps out engine noise, heat, and dirt did not survive removal and replacement as we worked on the steering box and brake master cylinder. We made a cardboard template from the old one, extending its length to cover brake and clutch pedal openings that were (not) closed by the perished draft seals. As might have been expected, the pattern wasn't quite right the first time. 

We found a doormat at Target that seemed about right for material. I drew the template in iDraw and passed it to Dr. Mark, who converted it to a vector file and cut it out on his garage laser cutter. The pedal holes weren't spaced correctly, so grandson David use his digital caliper to remeasure them. The second one we cut fits well; just need to screw or glue it down. 


Laser cutter at work on the Target doormat
Completed floor pad, version 1



















'56 Desoto engine showing the proper air cleaner
Found an old MOPAR air cleaner on eBay, bought it, and cleaned it up. We made an air filter gasket for it, but the air cleaner won't fit over the power steering pump. We really need one with a big notch on the bottom to clear the pump. A filter from a 56 ought to fit I would think. 

While test driving, the ignition switch fell out the back of the dash board. Found a screw and washer on the floor while working on the pad. Could be related. 

Sunday, June 23, 2013

Motor News [John]

Phil scraped the grease off the engine serial number. Although the car is a 1953 Firedome, built with a 276 cu in hemi V-8, the serial number decodes to a 1956 Firedome 330 cu in hemi. The 276 claimed 160 HP; the 330 claimed 230 HP with 2-barrel carb. The accessories on the engine might be a mix of 1953 and 1956 parts. The generator has a power steering pump on the back of it, and unless the pair of drive belts are removed, the pump interferes with the used oil-bath air cleaner we found. With longer belts, it looks like it can be made to fit, but there won't be much adjustment in the generator support strap unless we extend it.
This finding narrows our observations slightly. Since this is not the original motor, or even the same displacement, we're not very interested in heading for an as-bult restoration. Not that we ever were. On the other hand, another 70 horsepower is not all bad. This is a heavy car, and with the tip-toe automatic transmission, it's pretty sluggish.

The Letters, continued [John]

I mentioned in my missing parts post that we need a complete set of DESOTO letters for the tailgate and an S for the hood. These occasionally pop up on eBay, and in fact, my daughter bought a set as a gift. When they arrived, we found they were in disappointingly poor condition, and the S was bent badly. Condition is probably average, considering their age, but we are not at all sure we can straighten the S without breaking it.
The "new" old letters
So the new status of letters is we need two Ss, and if we decide to use these, they will all probably have to be cleaned up and rechromed. 
Given all that, and given that my son-in-law Dr Mark has a newly imported laser cutter in his garage, we investigated some alternatives. I looked for a suitable font on the web, and found some candidates. I distorted the proportions to make them fit in the same size rectangle the originals use. and I got the first 5 results shown. 
Meanwhile Mark traced a photo of the originals using a drawing program and came up with the sixth line shown. Local viewers all agreed that the factory font was much nicer looking than any I had found. 

Mark cut a set of the traced letters shown in the last line from a 1/8th-inch sheet of black acrylic. The arms of the T turned out very thin, unlikely to stand up to a car wash. Close examination of the original chromed pot metal letters reveals they are beveled: the delicate face of each letter is backed up by a stronger, larger, thicker piece of material. The laser cutter, although computer controlled and very precise, can only cut vertically, so it can't reproduce the bevel of the originals. However, we came up with an alternative: make a second set of letters, in the same or a contrasting color acrylic, such that the outline of each letter is everywhere a millimeter outside the outline of the first copy. Glue the two together for added strength, and then attach them to the body using some kind of automotive grade double-stick pad. The pad can be cut by the laser to exactly fit the outline of the larger set. Here's how they came out:
And here's a closer look at the first two. These are just stacked and not properly registered.
Laser-cut acrylic letters
Not sure we will use these yet. They are consistent with our emerging goals for restoration in that we are not concerned about restoring the car to completely as-built. Might not last forever in sunlight, but it's a simple matter to cut a couple of spare sets. We might still find originals, but if we have to restore and rechrome, not sure it's worth the money compared to this slightly custom touch. If we do use them, the color of each layer is negotiable. Needs to be visible on whatever paint we pick, and might look more elegant if the top copy contrasts with the lower, larger copy. Opinions welcome.




The Brakes [John]

The brakes were bad. We found the master cylinder was full of debris, had weak seals and a nonexistent boot. We rebuilt it first, then pulled off a front wheel and drum. These cars have two single-acting cylinders on the front brakes, and both of these were dripping fluid. The shoes have a good amount of lining on them, but they were wet with brake fluid. There is a variety of advice on how to deal with this on the web, including some that recommends waiting until your wife isn't home, pulling the shoes and baking them in a hot oven "until they quit smoking." We tried a less agressive approach: spraying thoroughly with brake cleaner, wiping them off, and repeating. They look much better, and we will see how they work in a week or two. One of the shoe retractor springs was broken, but we found one in the NAPA catalog that had similar measurements to replace it.
Next was the driver's side rear drum. Another Chrysler innovation was to rivet the rear drums to the week hub, which in turn fits a keyed taper on the axle shaft. We located a puller for the job and ordered it, and with it the drum came off without too much fuss. Phil put the axle nut back on the axle before he applied the puller. This is recommended to protect the axle from spreading under the pointed end of the puller and to catch the drum when the taper suddenly breaks free. Phil says he was very glad he remembered to put the nut back on. We actually wound up with two of these pullers, and will be glad to part with one of them.
Heavy duty hub puller
The rear drum brakes have a single, double-acting cylinder. Although the cylinder was dry, these shoes were wet too. Stepping on the brake pedal produced no fluid at the rear cylinder. Eventually we found that the short hose that connects the frame-mounted brake line to the Y-connector on the axle was packed full and would pass no air or fluid. Replacing the hose cured that, and the rear wheel assembly is now back together and ready for bleeding and adjustment next weekend, when we hope to rebuild the remaining two weeks.

Monday, May 27, 2013

Parts Needed [John]

1953 DeSoto Parts Wanted

Please contact me with leads or offers. Anyone know of a 53 wagon in salvage? 

John Boyd

Drjohn96@icloud.com; 858 997-7002

San Diego


Looking for a few parts for my 1953 DeSoto Estate Wagon fix-up project.


1.     Oil-bath air cleaner. Carburetor is a Carter BBD, and I measure the OD of the opening at 2-9/16 in. Might not have to be DeSoto if the throat diameter is right. Need the clamp too of course.



2.     DESOTO letters for the tailgate. The S has two pins and the others appear to have only one/ Not sure what the theory is for keeping them straight.

3.     The S for the hood. Thought we had that, but it seems to be gone.


4.     What is the content of the hood medallion supposed to be? Mine appears to be almost blank, but there might be a head of Hernando DeSoto in it. Anyone have a replacement? A photo?

5.     Moldings for rear fenders, both sides.

6.     Draft seals for the clutch and brake pedals. These are oval stampings with a slotted, rubber or fabric fill to keep engine compartment air out of the cabin.

7.     My car was built with power-assisted brakes, but the booster that should be at the master cylinder under the floorboard is gone. Might want to replace that if I can find one.

8.     Advice. Should this car have welting between the rear fenders and the body?

9.     Rear license plate bracket and lamp. The original bolts to the body below the tailgate, and it should have a lamp fixture that fits the rectangular hole just visible under the edge of the bumper.

10. Windshield wiper towers.  Chrome castings that hold the wiper armature bearing in place. I also need the wiper arms, but I might find those new at a parts store. The first photo is my car; the second is a 53 Chrysler that has the towers. I presume the DeSoto towers are similar to the Chrysler.






Steering Box is Fixed! [John]

We decided to hire a mechanic to remove and replace the steering box, which gushed fluid as long as the reservoir was not empty. He quoted a decent price, but found the job much harder than he anticipated. He sent the box to a rebuilder and we now have it back. No apparent leaks and the car has power steering. (The steering wheel needs centering though. Somehow that got messed up.) We settled the price amicably at somewhat higher than he had quoted.

All told, the car was at the shop for nearly a month. Mrs. B bore up well for the whole period, disappointed and lonely as she was for the smells of exhaust, leaking gas, mold and mildew, and consoled herself by parking her own car in the temporarily vacant garage stall.

Once the car was back, we scheduled a work day: Phil, me, Larry, and Guy for part of the time. Installed a throttle return spring, hooked it to a jury-rigged but neat bracket under a manifold bolt, replaced the sloppy, spring-free, hood hinges with some 1952 Chrysler hinges (with springs) I had found on eBay, and spent a few hours trying to invent a way to align the hood. Eventually we got tired of this and moved on to other details, like replacing a missing bumper bolt and then bolting a junk-yard licence plate frame to the rear bumper. I neatened up the ignition wiring, and we called it a day.

A hitch: The springs are not strong enough to support the hood -- you still need a prop rod. I'm sure this is not the intent; something is wrong. Do springs tire and weaken with age? Is there some restorative? And then, another hitch: the S from the hood DESOTO legend went missing. It had fallen off the first time I closed the hood, but I kept it safe in the glove box. On work day we took it out and looked for speed nuts or something in our garage junk to hold it on, and in the process we noted that none of the other letters had any attachment except gravity and a tiny bit of friction. At the end of the day, and today too, the S was gone. Most likely I picked it up and carried it around, then set it down somewhere in the house. Mrs. B assures me it will turn up. I'm less confident. But I can say it is not in the trash bin or the recycle bin and it is not in the garage. Oh, well. We need the full set of letters for the tailgate, just have to get an extra S.

Later, I found the hood alignment section of the factory service manual. It describes a simple, 20-step process to align the hood. For example, loosen the two rear bolts on the hinge plate and drive the forward end down with a hammer and a blunt drift. And, if the clearance to the fender is too tight, loosen all fender attaching bolts and move the fender.... This is for some later day.

The car doesn't run very well, although we do know how to work the gear selector now. But we are getting unanimous advice to fix the brakes first and then make it run better. Other recent advice confirms some earlier opinions to not replace the engine. No need to convert to 12v either. Especially not in a warm climate.

So far, it's fun, kind of.


Monday, March 11, 2013

What We Call "The Fuel Pump Affair" [Phil]

You'll recall our fuel pump developed a fault, in the form of a ruptured diaphragm. This allows fuel to enter the upper chamber, and escape through the vent into the atmosphere. The result, of course, is pretty lousy fuel economy. Unacceptably lousy. We needed a fix.

We opened two lines of inquiry.
1) We shopped for a rebuild kit
2) We shopped for a replacement

The pump is a Carter 2241S. We searched and searched, and finally didn't find any. But we did find Hot Heads Hemis, and they sell an adapter that enables use of a more recent, easily obtainable mechanical fuel pump. So we ordered the pump and adapter.

In a short while (I give these guys an A+ for dispatch) their parcel arrived, and last weekend we went to work. The adapter is truly a spacer that extends the distance between the timing chest and the pump body by about an inch. It is packaged with correct-length hex-head bolts, and a gasket, ready to use.

Access is a little tight, and one works from below and above, and below and above to plumb and mount the new parts. But in the end all was in place. Cranking the engine, however, produced no flow from the new pump. Hmmm.

We swapped input and output lines, to make certain it wasn't so simple a fault, but nope, no gas to the carb.

So we took it all apart again, and convinced ourselves there was no problem with the new pump - no, it worked just fine on the bench, and we verified which port was 'in' and which was 'out'. Then, we measured the lever arms of the old and new pumps, and convinced ourselves that the new pump may well be installed absent the adapter. Which we then did.

That did it - Without the adapter/spacer the new pump instantly delivered a healthy flow through the filter and to the carb, and presto! we were running on 8.

So if you're looking to replace that leaky old fuel pump on your 276 cu in 1953 Desoto Hemi, I recommend the Hot Heads Hemi item code 80562, description "318 fuel pump" as a bolt-on replacement for the Carter 2241S. It has minor differences, but works perfectly, and at $29.95 is not even expensive!